AR# 73079

2019.2 Zynq UltraScale+ MPSoC: Linux のブート時に PetaLinux ZCU106 BSP で SD カードの FAT32 または EXT4 パーティションが検出されない

説明

PetaLinux 2019.2 では、Linux のブート時に PetaLinux ZCU106 BSP で SD カード (例: SanDisk Ultra 64 GB MicroSDXC クラス 10 UHS メモリ カード) の FAT32 または EXT4 パーティションが検出されません。

この問題は、2019.2 ZCU106 VCU TRD PetaLinux プロジェクトおよび構築済みのイメージでも発生することがあります。

Xilinx Zynq MP First Stage Boot Loader
Release 2019.2   Oct 25 2019  -  09:07:59
NOTICE:  ATF running on XCZU7EV/silicon v4/RTL5.1 at 0xfffea000
NOTICE:  BL31: Secure code at 0x0
NOTICE:  BL31: Non secure code at 0x10080000
NOTICE:  BL31: v2.0(release):xilinx-v2019.1-12-g713dace9
NOTICE:  BL31: Built : 09:18:48, Oct 25 2019
PMUFW:  v1.1
U-Boot 2019.01 (Oct 25 2019 - 09:04:33 +0000)
 
Model: ZynqMP ZCU106 RevA
Board: Xilinx ZynqMP
DRAM:  4 GiB
EL Level:       EL2
Chip ID:        zu7ev
MMC:   mmc@ff170000: 0
Loading Environment from SPI Flash...SF: Detected n25q512a with page size 512 Bytes, erase size 128 KiB, total 128 MiB
OK
In:    serial@ff000000
Out:   serial@ff000000
Err:   serial@ff000000
Model: ZynqMP ZCU106 RevA
Board: Xilinx ZynqMP
Net:   ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id
eth0: ethernet@ff0e0000
Hit any key to stop autoboot:  0
Device: mmc@ff170000
Manufacturer ID: 3
OEM: 5344
Name: SB16G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.8 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
111705444 bytes read in 7189 ms (14.8 MiB/s)
## Loading kernel from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'kernel@1' kernel subimage
     Description:  Linux kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x10000108
     Data Size:    18082304 Bytes = 17.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00080000
     Entry Point:  0x00080000
     Hash algo:    sha1
     Hash value:   7a218e7055ee60902c0d0699d6bba7eacae3c158
   Verifying Hash Integrity ... sha1+ OK
## Loading ramdisk from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'ramdisk@1' ramdisk subimage
     Description:  petalinux-user-image
     Type:         RAMDisk Image
     Compression:  gzip compressed
     Data Start:   0x11149ee8
     Data Size:    93575401 Bytes = 89.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: unavailable
     Entry Point:  unavailable
     Hash algo:    sha1
     Hash value:   89174846ed278d1ecc5d9cf7ac7d3dc1b177434b
   Verifying Hash Integrity ... sha1+ OK
## Loading fdt from FIT Image at 10000000 ...
   Using 'conf@system-top.dtb' configuration
   Trying 'fdt@system-top.dtb' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x1113ec0c
     Data Size:    45591 Bytes = 44.5 KiB
     Architecture: AArch64
     Hash algo:    sha1
     Hash value:   2b18d0b4df1cf85fe84552996abf6ad2873f9d3a
   Verifying Hash Integrity ... sha1+ OK
   Booting using the fdt blob at 0x1113ec0c
   Loading Kernel Image ...OK
   Loading Ramdisk to 026c2000, end 07fff8e9 ...OK
   Loading Device Tree to 00000000026b3000, end 00000000026c1216 ...OK
 
Starting kernel ...
 
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 4.19.0-xilinx-v2019.2 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP Fri Oct 25 09:03:24 UTC 2019
[    0.000000] Machine model: ZynqMP ZCU106 RevA
[    0.000000] earlycon: cdns0 at MMIO 0x00000000ff000000 (options '115200n8')
[    0.000000] bootconsole [cdns0] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 1700 MiB at 0x0000000015800000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] random: get_random_bytes called from start_kernel+0x94/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s53656 r8192 d32360 u94208
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1033987
[    0.000000] Kernel command line: console=ttyPS0,115200n8 earlycon clk_ignore_unused cma=1700M
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] software IO TLB: mapped [mem 0x11800000-0x15800000] (64MB)
[    0.000000] Memory: 2212676K/4193280K available (10748K kernel code, 634K rwdata, 5424K rodata, 832K init, 314K bss, 239804K reserved, 1740800K cma-reserved)
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x170f8de2d3, max_idle_ns: 440795206112 ns
[    0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns
[    0.008238] Console: colour dummy device 80x25
[    0.012392] Calibrating delay loop (skipped), value calculated using timer frequency..199.98 BogoMIPS (lpj=399960)
[    0.022756] pid_max: default: 32768 minimum: 301
[    0.027447] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.034013] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.041792] ASID allocator initialised with 32768 entries
[    0.046508] rcu: Hierarchical SRCU implementation.
[    0.051534] EFI services will not be available.
[    0.055829] smp: Bringing up secondary CPUs ...
[    0.060485] Detected VIPT I-cache on CPU1
[    0.060512] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.060815] Detected VIPT I-cache on CPU2
[    0.060834] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.061122] Detected VIPT I-cache on CPU3
[    0.061141] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.061184] smp: Brought up 1 node, 4 CPUs
[    0.095682] SMP: Total of 4 processors activated.
[    0.100355] CPU features: detected: 32-bit EL0 Support
[    0.106978] CPU: All CPU(s) started at EL2
[    0.109535] alternatives: patching kernel code
[    0.114788] devtmpfs: initialized
[    0.122252] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.126920] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.168476] xor: measuring software checksum speed
[    0.205224]    8regs     :  2375.000 MB/sec
[    0.245258]    8regs_prefetch:  2052.000 MB/sec
[    0.285280]    32regs    :  2724.000 MB/sec
[    0.325309]    32regs_prefetch:  2308.000 MB/sec
[    0.325350] xor: using function: 32regs (2724.000 MB/sec)
[    0.329651] pinctrl core: initialized pinctrl subsystem
[    0.335436] NET: Registered protocol family 16
[    0.339505] audit: initializing netlink subsys (disabled)
[    0.344678] audit: type=2000 audit(0.296:1): state=initialized audit_enabled=0 res=1
[    0.352332] cpuidle: using governor menu
[    0.356316] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[    0.363559] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.370981] DMA: preallocated 256 KiB pool for atomic allocations
[    0.390771] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.459017] raid6: int64x1  gen()   448 MB/s
[    0.527027] raid6: int64x1  xor()   449 MB/s
[    0.595129] raid6: int64x2  gen()   684 MB/s
[    0.663123] raid6: int64x2  xor()   598 MB/s
[    0.731190] raid6: int64x4  gen()   981 MB/s
[    0.799215] raid6: int64x4  xor()   736 MB/s
[    0.867243] raid6: int64x8  gen()  1165 MB/s
[    0.935301] raid6: int64x8  xor()   759 MB/s
[    1.003364] raid6: neonx1   gen()   736 MB/s
[    1.071393] raid6: neonx1   xor()   879 MB/s
[    1.139431] raid6: neonx2   gen()  1129 MB/s
[    1.207464] raid6: neonx2   xor()  1171 MB/s
[    1.275538] raid6: neonx4   gen()  1482 MB/s
[    1.343557] raid6: neonx4   xor()  1416 MB/s
[    1.411621] raid6: neonx8   gen()  1563 MB/s
[    1.479641] raid6: neonx8   xor()  1459 MB/s
[    1.479679] raid6: using algorithm neonx8 gen() 1563 MB/s
[    1.483635] raid6: .... xor() 1459 MB/s, rmw enabled
[    1.488566] raid6: using neon recovery algorithm
[    1.493946] SCSI subsystem initialized
[    1.497038] usbcore: registered new interface driver usbfs
[    1.502353] usbcore: registered new interface driver hub
[    1.507629] usbcore: registered new device driver usb
[    1.512677] media: Linux media interface: v0.10
[    1.517137] videodev: Linux video capture interface: v2.00
[    1.522587] pps_core: LinuxPPS API ver.1 registered
[    1.527495] pps_core: Software ver.5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.536590] PTP clock support registered
[    1.540488] EDAC MC: Ver: 3.0.0
[    1.543978] zynqmp-ipi-mbox mailbox@ff990400: Probed ZynqMP IPI Mailbox driver.
[    1.551099] FPGA manager framework
[    1.554413] Advanced Linux Sound Architecture Driver Initialized.
[    1.560554] Bluetooth: Core ver 2.22
[    1.563843] NET: Registered protocol family 31
[    1.568242] Bluetooth: HCI device and connection manager initialized
[    1.574559] Bluetooth: HCI socket layer initialized
[    1.579402] Bluetooth: L2CAP socket layer initialized
[    1.584434] Bluetooth: SCO socket layer initialized
[    1.589550] clocksource: Switched to clocksource arch_sys_counter
[    1.595396] VFS: Disk quotas dquot_6.6.0
[    1.599252] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.610500] NET: Registered protocol family 2
[    1.610890] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[    1.618224] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.625536] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    1.632291] TCP: Hash tables configured (established 32768 bind 32768)
[    1.638459] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    1.644439] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    1.650916] NET: Registered protocol family 1
[    1.655306] RPC: Registered named UNIX socket transport module.
[    1.660984] RPC: Registered udp transport module.
[    1.665651] RPC: Registered tcp transport module.
[    1.670323] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.677068] Trying to unpack rootfs image as initramfs...
[    5.827687] Freeing initrd memory: 91380K
[    5.828314] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    5.833341] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    5.841832] Initialise system trusted keyrings
[    5.845336] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[    5.852349] NFS: Registering the id_resolver key type
[    5.856703] Key type id_resolver registered
[    5.860844] Key type id_legacy registered
[    5.864828] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    5.871495] jffs2: version 2.2.(NAND) 2001-2006 Red Hat, Inc.
[    6.965081] NET: Registered protocol family 38
[    7.025662] Key type asymmetric registered
[    7.025700] Asymmetric key parser 'x509' registered
[    7.028994] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    7.036330] io scheduler noop registered
[    7.040209] io scheduler deadline registered
[    7.044478] io scheduler cfq registered (default)
[    7.049119] io scheduler mq-deadline registered
[    7.053616] io scheduler kyber registered
[    7.059348] xilinx-frmbuf a00f0000.v_frmbuf_rd: Probe deferred due to GPIO reset defer
[    7.065513] xilinx-frmbuf a0200000.v_frmbuf_wr: Probe deferred due to GPIO reset defer
[    7.100808] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    7.105204] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    7.112099] brd: module loaded
[    7.115924] loop: module loaded
[    7.116833] mtdoops: mtd device (mtddev=name/number) must be supplied
[    7.121410] libphy: Fixed MDIO Bus: probed
[    7.125335] tun: Universal TUN/TAP device driver, 1.6
[    7.129313] CAN device driver interface
[    7.134076] usbcore: registered new interface driver asix
[    7.138412] usbcore: registered new interface driver ax88179_178a
[    7.144449] usbcore: registered new interface driver cdc_ether
[    7.150244] usbcore: registered new interface driver net1080
[    7.155871] usbcore: registered new interface driver cdc_subset
[    7.161750] usbcore: registered new interface driver zaurus
[    7.167294] usbcore: registered new interface driver cdc_ncm
[    7.173427] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.179376] ehci-pci: EHCI PCI platform driver
[    7.184085] usbcore: registered new interface driver uas
[    7.189098] usbcore: registered new interface driver usb-storage
[    7.195564] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc0
[    7.202278] i2c /dev entries driver
[    7.207523] usbcore: registered new interface driver uvcvideo
[    7.211384] USB Video Class driver (1.1.1)
[    7.216495] Bluetooth: HCI UART driver ver 2.3
[    7.219867] Bluetooth: HCI UART protocol H4 registered
[    7.224967] Bluetooth: HCI UART protocol BCSP registered
[    7.230262] Bluetooth: HCI UART protocol LL registered
[    7.235346] Bluetooth: HCI UART protocol ATH3K registered
[    7.240728] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    7.246980] Bluetooth: HCI UART protocol Intel registered
[    7.252319] Bluetooth: HCI UART protocol QCA registered
[    7.257522] usbcore: registered new interface driver bcm203x
[    7.263142] usbcore: registered new interface driver bpa10x
[    7.268680] usbcore: registered new interface driver bfusb
[    7.274128] usbcore: registered new interface driver btusb
[    7.279551] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
[    7.285218] usbcore: registered new interface driver ath3k
[    7.290753] EDAC MC: ECC not enabled
[    7.294403] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT)
[    7.306986] sdhci: Secure Digital Host Controller Interface driver
[    7.312425] sdhci: Copyright(c) Pierre Ossman
[    7.316749] sdhci-pltfm: SDHCI platform and OF driver helper
[    7.322713] ledtrig-cpu: registered to indicate activity on CPUs
[    7.328388] zynqmp_firmware_probe Platform Management API v1.1
[    7.334144] zynqmp_firmware_probe Trustzone version v1.0
[    7.342197] zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: zynqmp pinctrl initialized
[    7.370166] zynqmp_clk_mux_get_parent() getparent failed for clock: lpd_wdt, ret = -22
[    7.372892] alg: No test for xilinx-zynqmp-aes (zynqmp-aes)
[    7.377999] zynqmp_aes zynqmp_aes: AES Successfully Registered
[    7.377999]
[    7.385517] alg: No test for xilinx-keccak-384 (zynqmp-keccak-384)
[    7.391648] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa)
[    7.397226] usbcore: registered new interface driver usbhid
[    7.402552] usbhid: USB HID core driver
[    7.408652] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered
[    7.413158] usbcore: registered new interface driver snd-usb-audio
[    7.419855] pktgen: Packet Generator for packet performance testing.Version: 2.75
[    7.426781] Initializing XFRM netlink socket
[    7.430734] NET: Registered protocol family 10
[    7.435413] Segment Routing with IPv6
[    7.438793] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    7.444914] NET: Registered protocol family 17
[    7.449006] NET: Registered protocol family 15
[    7.453420] bridge: filtering via arp/ip/ip6tables is no longer available by default.Update your scripts to load br_netfilter if you need this.
[    7.466336] can: controller area network core (rev 20170425 abi 9)
[    7.472468] NET: Registered protocol family 29
[    7.476854] can: raw protocol (rev 20170425)
[    7.481090] can: broadcast manager protocol (rev 20170425 t)
[    7.486715] can: netlink gateway (rev 20170425) max_hops=1
[    7.492221] Bluetooth: RFCOMM TTY layer initialized
[    7.497015] Bluetooth: RFCOMM socket layer initialized
[    7.502128] Bluetooth: RFCOMM ver 1.11
[    7.505836] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    7.511108] Bluetooth: BNEP filters: protocol multicast
[    7.516302] Bluetooth: BNEP socket layer initialized
[    7.521231] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    7.527115] Bluetooth: HIDP socket layer initialized
[    7.532161] 9pnet: Installing 9P2000 support
[    7.536298] Key type dns_resolver registered
[    7.540911] registered taskstats version 1
[    7.544593] Loading compiled-in X.509 certificates
[    7.549688] Btrfs loaded, crc32c=crc32c-generic
[    7.560168] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 42, base_baud = 6249375) is a xuartps
[    7.569565] console [ttyPS0] enabled
[    7.569565] console [ttyPS0] enabled
[    7.573157] bootconsole [cdns0] disabled
[    7.573157] bootconsole [cdns0] disabled
[    7.581238] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 43, base_baud = 6249375) is a xuartps
[    7.594618] of-fpga-region fpga-full: FPGA Region probed
[    7.600797] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed
[    7.607386] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success
[    7.614492] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success
[    7.621600] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success
[    7.628702] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success
[    7.635804] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success
[    7.642909] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success
[    7.650015] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success
[    7.657117] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success
[    7.664289] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success
[    7.671397] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success
[    7.678493] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success
[    7.685604] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success
[    7.692707] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success
[    7.699809] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success
[    7.706913] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success
[    7.714021] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success
[    7.721125] xilinx-frmbuf a00f0000.v_frmbuf_rd: Xilinx AXI frmbuf DMA_MEM_TO_DEV
[    7.728573] xilinx-frmbuf a00f0000.v_frmbuf_rd: Xilinx AXI FrameBuffer Engine Driver Probed!!
[    7.737213] xilinx-frmbuf a0200000.v_frmbuf_wr: Xilinx AXI frmbuf DMA_DEV_TO_MEM
[    7.744663] xilinx-frmbuf a0200000.v_frmbuf_wr: Xilinx AXI FrameBuffer Engine Driver Probed!!
[    7.753526] xilinx-psgtr fd400000.zynqmp_phy: Lane:1 type:8 protocol:4 pll_locked:yes
[    7.764527] xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed
[    7.775234] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed
[    7.783269] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed
[    7.791878] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok
[    7.804320] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok
[    7.817005] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xilinx DisplayPort Sound Card probed
[    7.827200] OF: graph: no port node found in /amba/zynqmp-display@fd4a0000
[    7.834223] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    7.840828] [drm] No driver support for vblank timestamp query.
[    7.846798] xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8008bbeb78)
[    8.933563] [drm] Cannot find any crtc or sizes
[    8.938316] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0
[    8.946417] zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsystem driver probed
[    8.955398] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:3 protocol:2 pll_locked:yes
[    8.963280] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    8.972236] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
[    8.982706] scsi host0: ahci-ceva
[    8.986295] scsi host1: ahci-ceva
[    8.989753] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 40
[    8.997669] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 40
[    9.006640] m25p80 spi0.0: n25q512a (131072 Kbytes)
[    9.011534] 3 fixed-partitions partitions found on MTD device spi0.0
[    9.017884] Creating 3 MTD partitions on "spi0.0":
[    9.022670] 0x000000000000-0x000001e00000 : "boot"
[    9.027925] 0x000001e00000-0x000001e40000 : "bootenv"
[    9.033368] 0x000001e40000-0x000005a40000 : "kernel"
[    9.040797] macb ff0e0000.ethernet: Not enabling partial store and forward
[    9.048162] libphy: MACB_mii_bus: probed
[    9.057037] TI DP83867 ff0e0000.ethernet-ffffffff:0c: attached PHY driver [TI DP83867] (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:0c, irq=POLL)
[    9.070085] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 30 (00:0a:35:04:e8:19)
[    9.080269] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM
[    9.086816] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM
[    9.093316] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM
[    9.099799] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM
[    9.107648] dwc3 fe200000.dwc3: Failed to get clk 'ref': -2
[    9.113511] xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes
[    9.121757] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    9.127251] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    9.135233] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x0000000202010810
[    9.144641] xhci-hcd xhci-hcd.0.auto: irq 52, io mem 0xfe200000
[    9.150765] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[    9.159023] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    9.166241] usb usb1: Product: xHCI Host Controller
[    9.171110] usb usb1: Manufacturer: Linux 4.19.0-xilinx-v2019.2 xhci-hcd
[    9.177803] usb usb1: SerialNumber: xhci-hcd.0.auto
[    9.182957] hub 1-0:1.0: USB hub found
[    9.186724] hub 1-0:1.0: 1 port detected
[    9.190831] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    9.196318] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    9.203976] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    9.210704] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[    9.218967] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    9.226183] usb usb2: Product: xHCI Host Controller
[    9.231052] usb usb2: Manufacturer: Linux 4.19.0-xilinx-v2019.2 xhci-hcd
[    9.237744] usb usb2: SerialNumber: xhci-hcd.0.auto
[    9.242864] hub 2-0:1.0: USB hub found
[    9.246636] hub 2-0:1.0: 1 port detected
[    9.251702] pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator
[    9.258954] pca953x 0-0020: Linked as a consumer to regulator.0
[    9.265612] pca953x 0-0021: 0-0021 supply vcc not found, using dummy regulator
[    9.272846] pca953x 0-0021: Linked as a consumer to regulator.0
[    9.280149] ina2xx 3-0040: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.286932] ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.293711] ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.300490] ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.307275] ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.314066] ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.320850] ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.322687] ata1: SATA link down (SStatus 0 SControl 330)
[    9.327643] ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.332619] ata2: SATA link down (SStatus 0 SControl 330)
[    9.339376] ina2xx 3-004a: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.351110] ina2xx 3-004b: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.357487] i2c i2c-0: Added multiplexed i2c bus 3
[    9.362903] ina2xx 4-0040: power monitor ina226 (Rshunt = 2000 uOhm)
[    9.369687] ina2xx 4-0041: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.376467] ina2xx 4-0042: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.383250] ina2xx 4-0043: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.390038] ina2xx 4-0044: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.396822] ina2xx 4-0045: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.403601] ina2xx 4-0046: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.410390] ina2xx 4-0047: power monitor ina226 (Rshunt = 5000 uOhm)
[    9.416767] i2c i2c-0: Added multiplexed i2c bus 4
[    9.440036] random: fast init done
[    9.458940] i2c i2c-0: Added multiplexed i2c bus 5
[    9.463853] i2c i2c-0: Added multiplexed i2c bus 6
[    9.468644] pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544
[    9.475973] cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 32
[    9.483644] at24 7-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
[    9.490370] i2c i2c-1: Added multiplexed i2c bus 7
[    9.495361] i2c i2c-1: Added multiplexed i2c bus 8
[    9.502231] si570 9-005d: registered, current frequency 300000000 Hz
[    9.508611] i2c i2c-1: Added multiplexed i2c bus 9
[    9.525557] si570 10-005d: registered, current frequency 148500000 Hz
[    9.532021] i2c i2c-1: Added multiplexed i2c bus 10
[    9.537095] si5324 11-0069: si5328 probed
[    9.597845] si5324 11-0069: si5328 probe successful
[    9.602748] i2c i2c-1: Added multiplexed i2c bus 11
[    9.607829] i2c i2c-1: Added multiplexed i2c bus 12
[    9.612828] i2c i2c-1: Added multiplexed i2c bus 13
[    9.617821] i2c i2c-1: Added multiplexed i2c bus 14
[    9.622695] pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548
[    9.630601] i2c i2c-1: Added multiplexed i2c bus 15
[    9.635607] i2c i2c-1: Added multiplexed i2c bus 16
[    9.640605] i2c i2c-1: Added multiplexed i2c bus 17
[    9.645984] i2c i2c-1: Added multiplexed i2c bus 18
[    9.650996] i2c i2c-1: Added multiplexed i2c bus 19
[    9.656005] i2c i2c-1: Added multiplexed i2c bus 20
[    9.661010] i2c i2c-1: Added multiplexed i2c bus 21
[    9.666023] i2c i2c-1: Added multiplexed i2c bus 22
[    9.670898] pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548
[    9.678490] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 33
[    9.687135] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s
[    9.694578] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer with timeout 10s
[    9.702087] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1199880 KHz
[    9.709538] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1199999 KHz
[    9.749555] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit
[    9.770159] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    9.777116] rtc_zynqmp ffa60000.rtc: setting system clock to 2019-11-07 19:21:56 UTC (1573154516)
[    9.785990] of_cfs_init
[    9.788441] of_cfs_init: OK
[    9.791372] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    9.868034] mmc0: Tuning failed, falling back to fixed sampling clock
[    9.875600] mmc0: new ultra high speed SDR104 SDHC card at address aaaa
[    9.882740] mmcblk0: mmc0:aaaa SB16G 14.8 GiB
[    9.932839] mmc0: Tuning failed, falling back to fixed sampling clock
[    9.935741] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    9.945798] clk: Not disabling unused clocks
[    9.950064] ALSA device list:
[    9.953014]   #0: DisplayPort monitor
[    9.956941] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    9.965552] cfg80211: failed to load regulatory.db
[    9.970816] Freeing unused kernel memory: 832K
[    9.989578] Run /init as init process
INIT: version 2.88 booting
[   10.038042] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.078253] [drm] Cannot find any crtc or sizes
Starting udev
[   10.095227] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.102917] print_req_error: I/O error, dev mmcblk0, sector 0
[   10.114928] udevd[2001]: starting version 3.2.5
[   10.119766] random: udevd: uninitialized urandom read (16 bytes read)
[   10.126255] random: udevd: uninitialized urandom read (16 bytes read)
[   10.132756] random: udevd: uninitialized urandom read (16 bytes read)
[   10.143958] udevd[2002]: starting eudev-3.2.5
[   10.152655] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.160348] print_req_error: I/O error, dev mmcblk0, sector 1
[   10.202351] mali: loading out-of-tree module taints kernel.
[   10.210174] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.217865] print_req_error: I/O error, dev mmcblk0, sector 2
[   10.268400] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.276136] print_req_error: I/O error, dev mmcblk0, sector 3
[   10.326186] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.333920] print_req_error: I/O error, dev mmcblk0, sector 4
[   10.383793] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.391570] print_req_error: I/O error, dev mmcblk0, sector 5
[   10.441422] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.449138] print_req_error: I/O error, dev mmcblk0, sector 6
[   10.499709] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.507459] print_req_error: I/O error, dev mmcblk0, sector 7
[   10.513231] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   10.564688] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.616289] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.639728] xilinx-vcu xilinx-vcu: Could not get core_enc clock
[   10.648297] VCU PLL: enable
[   10.651703] xilinx-vcu xilinx-vcu: xvcu_probe: Probed successfully
[   10.667819] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.675537] print_req_error: I/O error, dev mmcblk0, sector 0
[   10.688717] al5e a0100000.al5e: l2 prefetch size:17530880 (bits), l2 color bitdepth:10
[   10.690028] al5d a0120000.al5d: l2 prefetch size:17530880 (bits), l2 color bitdepth:10
[   10.725337] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.733051] print_req_error: I/O error, dev mmcblk0, sector 1
[   10.782769] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.834341] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.885959] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.938116] mmc0: Tuning failed, falling back to fixed sampling clock
[   10.989798] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.041334] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.048938] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   11.056100]  mmcblk0: unable to read partition table
[   11.106793] mmc0: Tuning failed, falling back to fixed sampling clock
Configuring packages on first boot....
 (This may take several minutes.Please do not power off the machine.)
Running postinst /etc/rpm-postinsts/100-libmali-xlnx...
[   11.158409] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.164360] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0
[   11.209858] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.217897] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0
[   11.251764] Warn: update-alternatives: libmali-xlnx has multiple providers with the same priority, please check /usr/lib/opkg/alternatives/libmali-xlnx for details
[   11.261467] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.284284] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0
[   11.318047] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.337383] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0
Running postinst /etc/rpm-postinsts/101-sysvinit-inittab...
[   11.369660] mmc0: Tuning failed, falling back to fixed sampling clock
update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)
INIT: Entering runlevel: 5
Configuring network interfaces...[   11.421120] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.463444] pps pps0: new PPS source ptp0
[   11.467488] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered.
[   11.472720] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.474194] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc: started, v1.29.2
[   11.525485] mmc0: Tuning failed, falling back to fixed sampling clock
udhcpc: sending discover
[   11.576890] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.629279] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.680695] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.732062] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.783349] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.834636] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.885924] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.937130] mmc0: Tuning failed, falling back to fixed sampling clock
[   11.988497] mmc0: Tuning failed, falling back to fixed sampling clock
[   12.039784] mmc0: Tuning failed, falling back to fixed sampling clock
[   12.091156] mmc0: Tuning failed, falling back to fixed sampling clock
[   12.098764] Buffer I/O error on dev mmcblk0, logical block 3889520, async page read
[   12.494202] macb ff0e0000.ethernet eth0: link up (1000/Full)
[   12.499881] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
udhcpc: sending discover
udhcpc: sending select for 172.20.9.52
udhcpc: lease of 172.20.9.52 obtained, lease time 172800
/etc/udhcpc.d/50default: Adding DNS 172.20.20.202
/etc/udhcpc.d/50default: Adding DNS 172.20.60.202
/etc/udhcpc.d/50default: Adding DNS 172.20.60.201
done.
Starting system message bus: dbus.
Starting haveged: haveged: listening socket at 3
haveged: haveged starting up
Starting Xserver
Starting Dropbear SSH server:
Generating 2048 bit rsa key, this may take a while...
 
X.Org X Server 1.20.1
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.10.0-693.el7.x86_64 x86_64
Current Operating System: Linux xilinx-zcu106-2019_2 4.19.0-xilinx-v2019.2 #1 SMP Fri Oct 25 09:03:24 UTC 2019 aarch64
Kernel command line: console=ttyPS0,115200n8 earlycon clk_ignore_unused cma=1700M
Build Date: 25 October 2019  09:06:39AM
 
Current version of pixman: 0.34.0
        Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov  7 19:22:01 2019
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
haveged: haveged: ver: 1.9.4; arch: generic; vend: ; build: (gcc 8.2.0 CTV); collect: 128K
 
haveged: haveged: cpu: (VC); data: 16K (D); inst: 16K (D); idx: 11/40; sz: 15528/64688
 
haveged: haveged: tot tests(BA8): A:1/1 B:1/1 continuous tests(B):  last entropy estimate 8.00316
 
haveged: haveged: fills: 0, generated: 0
 
[   16.026741] random: crng init done
[   16.030145] random: 7 urandom warning(s) missed due to ratelimiting
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCJccTOO12mNYAgjVXmy7YIGaqY5oSH7STge+kqqfOSpPFWFJ04AT
q5H7g9LSBe8iJyjIOLHiWZgRVJ6ue1zPF8swa9utD4fcR4wRwY6YerUhDOvOoKeo2aJSHYJktQ640ntOib
0N5KyGc0Ua3HMAbfS12jW8Wgly2FWuZZKMhj8OZIVH/aJ2IDUnBKMcXYu0qGLDJo5dp/8IX3PfXdc/IlC0J+SfengHeEuF1ZSs+WyrdWgKR8oWF0KEa3IF7wd2qi2QIVQ83s5bl5kpbEpjDDhYXtkVqgvcXKj5x/3FxE0/PMbaGpPlUbpF00D84FNnAhmrB2tMRT6pkyN/dwozDp root@xilinx-zcu106-2019_2
Fingerprint: sha1!! c5:c2:50:11:22:ad:88:f3:3a:f3:9f:eb:96:8d:71:28:32:39:4e:f8
dropbear.
Starting internet superserver: inetd.
Starting syslogd/klogd: done
Starting tcf-agent: OK
 
PetaLinux 2019.2 xilinx-zcu106-2019_2 /dev/ttyPS0
 
xilinx-zcu106-2019_2 login: The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning:          Unsupported high keycode 372 for name <I372> ignored
>                   X11 cannot support keycodes above 255.
>                   This warning only shows for the first high keycode.
Errors from xkbcomp are not fatal to the X server
D-BUS per-session daemon address is: unix:abstract=/tmp/dbus-M3zDquoaFs,guid=4fc2da110e9d75b4b97af7565dc46edb
Failed to launch bus: Failed to execute child process ?/usr/bin? (Permission denied)matchbox: Cant find a keycode for keysym 269025056
matchbox: ignoring key shortcut XF86Calendar=!$contacts
matchbox: Cant find a keycode for keysym 2809
matchbox: ignoring key shortcut telephone=!$dates
 
matchbox: Cant find a keycode for keysym 269025050
matchbox: ignoring key shortcut XF86Start=!matchbox-remote -desktop
 
[settings daemon] Forking. run with -n to prevent fork
 
(matchbox-panel:2624): dbind-WARNING **: 19:22:03.627: Error retrieving accessibility bus address: org.a11y.Bus.Error: Failed to execute child process ?/usr/bin? (Permission denied)
 
(matchbox-desktop:2622): dbind-WARNING **: 19:22:03.627: Error retrieving accessibility bus address: org.a11y.Bus.Error: Failed to execute child process ?/usr/bin? (Permission denied)
 
PetaLinux 2019.2 xilinx-zcu106-2019_2 /dev/ttyPS0
 
xilinx-zcu106-2019_2 login: root
Password:
root@xilinx-zcu106-2019_2:~#
root@xilinx-zcu106-2019_2:~# mount
rootfs on / type rootfs (rw,size=1106336k,nr_inodes=276584)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
configfs on /sys/kernel/config type configfs (rw,relatime)
devtmpfs on /dev type devtmpfs (rw,relatime,size=1106336k,nr_inodes=276584,mode=755)
tmpfs on /run type tmpfs (rw,nosuid,nodev,mode=755)
tmpfs on /var/volatile type tmpfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620,ptmxmode=000)
root@xilinx-zcu106-2019_2:~#
root@xilinx-zcu106-2019_2:~# ls -l /dev/mmcblk0
brw-rw----    1 root     disk      179,   0 Nov  7 19:21 /dev/mmcblk0
root@xilinx-zcu106-2019_2:~#
root@xilinx-zcu106-2019_2:~#

ソリューション

これは 2019.2 ZCU106 BSP での既知の問題です。

この問題を修正するには、<plnx-proj-root>/project-spec/meta-user/recipes-bsp/device-tree/files/system-user.dtsi にデバイス ツリー ノード プロパティを追加する必要があります。

1) system-user.dtsi ファイルを次のように変更します。

$ vim /project-spec/meta-user/recipes-bsp/device-tree/files/system-user.dtsi
# system-user.dtsi content

"/include/ "system-conf.dtsi"
/ {
};

&sdhci1 {
        no-1-8-v;
};

 

2) デバイス ツリーの sstate キャッシュをクリーンにし、デバイス ツリーを再構築します。

$ petalinux-build -c device-tree -x cleansstate
$ petalinux-build -c device-tree

 

注記: このソリューションは、2019.2 ZCU106 VCU TRD PetaLinux BSP にも適用されます。

AR# 73079
日付 11/22/2019
ステータス アクティブ
種類 一般
デバイス
ツール
Boards & Kits